HSNH1300-42三螺桿泵、hsnh系列稀油站三螺桿泵
三螺桿泵/雙螺桿泵產品性能參數配置：
Three screw pump / double screw pump performance parameter configuration:
1、介質名稱：乳化液 切削液 磨消油 冷卻潤滑溶液 液壓油 密封油 水乙二醇 潤滑油 機械油 齒輪油 重載齒輪油 軋鋼機油汽輪機油 重油 燃料油 輕質燃油重質燃油 柴油 渣油 原油 瀝青
1, media name: emulsion cutting fluid grinding oil cooling lubrication solution of water glycol hydraulic oil seal oil and lubricating oil of mechanical oil gear oil gear oil for rolling mill oil turbine oil oil fuel oil light oil heavy oil dieseloil oil asphalt
2、介質溫度，是否含固體顆粒：-20攝氏度至90攝氏度，三螺桿泵不容許有固體顆粒，雙螺桿泵容許小于螺桿間隙柔性顆粒。
2, the temperature of the medium, whether or not containing solid particles: -20 degrees Celsius to 90 degrees Celsius, three screw pump does not allow for solid particles, double screw pump allows flexible particles less thanscrew clearance.
3、介質腐蝕性及PH值：介質的腐蝕性決定了泵過流部件的材料
3, corrosive medium and pH value: corrosive media determines the pump material
4、介質工作粘度：3—400mm2/s,對于粘度大于5000mm2/s的流體，
4, medium viscosity: 3 - 400mm2/s, the viscosity of the fluid is larger than 5000mm2/s,
5、螺桿泵的額定流量：20—9400L/min。
5 the rated flow, screw pump: 20 - 9400L/min.
6、螺桿泵的工作壓力：0—10Mpa
6, screw pump working pressure: 0 - 10Mpa
7、電機配置 ：功率 轉速750-/min—3600-/min 防護等級防爆等級等
7, the motor configuration: power speed 750-/min - 3600-/min protection grade explosion-proof grade etc.
8、泵進口通徑25—450 mm（螺桿泵的進出口管道通徑配置必須保證和泵進出口通徑保持*，保證泵的自吸能力和正常使用，否則要么產生汽蝕，要么導致泵無法正常工作，尤其是泵的安裝位置在液面之上的工況必須嚴格遵守。）
8, pump inlet diameter of 25 - 450 mm （screw pump import and export pipeline diameter configuration mustguarantee and the pump inlet and outlet path consistent, ensure the pump self-priming ability and normal,otherwise either cavitation, or the pump can not work normally, especially the pump installation position must be strictly observed. In above the liquid level condition）
9、泵出口通徑20—500mm
9, the pump outlet diameter 20 - 500mm
10、泵的自吸能力或汽蝕余量：螺桿泵的理論自吸高度約等于10減去螺桿泵的汽蝕余量的值（單位是米）其自吸能力不能超過10米即一個標準大氣壓產生的水柱。
10、Self absorption capacity or NPSH 10, pump: pump cavitation theory self suction height is about equal to 10 minusthe value of the screw pump （units are in meters） the self absorption capacity of not more than 10 meters is a standard atmospheric column.
11、泵安裝方式：臥式 立式 法蘭式（支架式） 懸掛式 柱腳立式
11, pump installation: horizontal vertical flange type （scaffolding） hanging column vertical
12、是否帶安全閥或溢流閥裝置：安全閥 溢流閥
12, whether with a safety valve and relief valve device: safety valve relief valve
13、其他附件如螺桿泵進出口配對法蘭 螺桿泵過濾器地腳螺栓 螺桿泵機械密封 軸承 聯軸器備件 以及螺桿泵的安裝工具
13, other accessories such as screw pump import and export the mating flange screw pump filter anchor boltscrew pump mechanical seal bearing coupling parts and installation tool for screw pump.
HSN三螺桿泵選型步驟及注意事項
HSN three screw pump selection steps and matters needing attention
首先要準確了解HSN三螺桿泵的實際工作參數，如壓力、流量、介質的工作溫度及介質在工作溫度下的粘度、介質有無潤滑性、腐蝕性等；
1, we should accuray understand the actual working parameters of the HSN three screw pump, such as the temperature and medium pressure, flow rate, medium viscosity at operating temperature, medium with and withoutlubrication, corrosion resistance;
根據介質在工作溫度下的粘度初步選擇泵的轉速，一般粘度小于300mm2/s，選擇n=1450r/min比較適合，當粘度大于300mm2/s，請慎重考慮泵的必需汽蝕余量，以免泵產生振動；
Preliminary selection of pump 2, according to the media at the operating temperature of the viscosity of thespeed, the general viscosity is less than 300mm2/s, n=1450r/min is more suitable, when the viscosity is greater than 300mm2/s, please consider carefully pump necessary NPSH, lest the pump vibration;
從泵的性能表上，按所需流量、壓力等參數初步選擇泵的規格；
3, from the pump performance table, according to the required flow and pressure, the preliminary selection ofpump size;
從泵的必需汽蝕表（P15）上，根據泵的規格轉速粘度查出泵的必需汽蝕余量NPSHr值；
4, from the pump required NPSH table （P15）, according to the size, speed, viscosity pump to pump necessary NPSH NPSHr value;
如果泵的必需汽蝕余量NPSHr值小于管道裝置的汽蝕余量NPSHa值，那么泵選型正確；如果泵的必需汽蝕余量NPSHr值大于管道裝置的汽蝕余量NPSHa值，則要選擇大一檔的泵或是降低轉速，并重新校合NPSHr值。NPSHr ≤ NPSHa+K（一般情況安全裕度 K取0.3—0.5m）
5, if the pump necessary NPSH NPSHr value is less than the pipeline device of NPSH NPSHa value, then the pumpselection is correct; if the pump necessary NPSH NPSHr value is greater than the pipeline device of NPSH NPSHa value, then to the choice of a pump or reduce speed, and re adjustment of NPSHr value. NPSHr ≤ NPSHa+K（general safety margin of K 0.3 - 0.5m）
選定泵的規格后，在對應的粘度下，從表中查出此規格泵在工作壓力下△P下的流量與軸功率N1，選配電機功率N2，N2 ≥ K·N1。N1（Kw） ≤5 5＜N1≤10 10＜N1≤50 ＞50K 1.25 1.2 1.15 1.1
6, the selected pump specifications, in the corresponding viscosity, from the table to identify the specifications of the pump in the work pressure △ P under the flow and shaft power N1, matching motor power N2, N2 ≥ K · N1. N1（Kw） ≤ 55 < N1 < 1010 < N1 > 50K 1.25 1.2 1.15 1.1 50
用戶選定泵后，根據泵的規格與電機的機組配套尺寸進行基礎施工設計，進出口管道必須與泵的進出口相匹配。
7, the user selected pump, foundation construction design according to the unit size specification of pump and motor, import and export pipeline must match the import and export of pumps.
如果您需要，我們技術部可替您選型，您須提供以下數據
8, if you need,our technical department for you selection, you must provide the following data
泵的工作流量 Q
The work flow of the Q pump
介質工作溫度 T
Medium temperature T
泵的進口壓力（或真空度） P1
Pump inlet pressure （or vacuum） P1
泵的出口壓力 P2
Outlet pressure of P2 pump
工作溫度下介質的粘度 v
The viscosity of V medium temperature
地面驅動螺桿泵采油技術特點
Technical characteristics of screw pump ground driving
1） 螺桿泵屬于旋轉容積式泵，兼有離心泵和容積泵的優點，可以解決常規抽油泵的油稠，卡砂和氣鎖現象；
screw pump belongs to a rotary positive displacement pump, which has the advantages of centrifugal pump andthe volume of the pump, can solve the conventional pump heavy oil, sand and air lock phenomenon card;
2） 螺桿泵在不同壓力條件下流量改變很小，流量非常均勻；
screw pump under different pressure conditions flow change is small, traffic is very uniform;
3） 運動件很少（只有轉子一個運動件），流道短且簡單，過流面積大，油流擾動小，故攜帶能力強；
moving parts （only a few rotor movement）, channel is short and simple, large flow area, the oil flow disturbanceis small, so the carrying capacity;
4） 采油生產投資費用低，對比常規抽油機，電動潛油泵等采油方式，螺桿泵結構簡單，一次性投資和維護費用zui低；
4） the production of low investment cost, compared with conventional pumping, electric submersible pump well,screw pump has the advantages of simple structure, one-time investment and maintenance cost;
5） 環境適應性強，適用于油稠、高含砂，高含氣等油井，使用占地面積小，安裝簡便。
5） strong environmental adaptability, suitable for heavy oil, high sand, oil wells with high gas containing, the use ofthe area is small, easy to install.
公 司 名稱： | 黃山天曼泵業有限公司 |
姓名： | 程曉 （銷售 ） （） |
辦 公 地址： | 中國 黃山市徽州區城北工業園 |
郵 編： | 245400 |
電 話： | 86- |
傳 真： | 86- |
移 動 ： | |
郵 箱： | Hstmby01 |
： | |
阿 里 旺旺: | 旺旺：hstmby01 |
公司主頁： | http;//www.hstmby.comhttp://www.luogb.com http://www.cntmby.comhttp://www.tm-p.cc |
Company name: Mount Huangshan teamon pump industry limited company
Contact person: Mr. Cheng Xiao （Sales Manager） （）
Office address: China Huangshan City Huizhou area north of the City Industrial Park
Postal Code: 245400
86-
86-
phone:
: Hstmby01
: :
A: I want to: hstmby01
Company homepage: http; //www.hstmby.comhttp://www.luogb.com
http://www.cntmby.comhttp://www.tm-p.cc
會員1.png)
